Software for tg-uv2




















I saw the bit about the voltages differences causing the error. Problem solved. I connected the cable and the drivers loaded ok. So far so good. I had to alter the com ports accordingly on the PC to allow it to work which is pretty standard anyway. When I interrogated the radio the PC read it but only pulled off certain channels and not others.

This software has the channels required to program the radio. The other radios probably have encode and decode programmed so you have to program the correct codes to match those radios. Carlos, sounds like you have programmed a split frequency or coding problem.

Check the transmits frequency and ensure it is the same as the receive frequency. Answering my own question here. It appears that these are the default starting frequencies the radio tunes to when you switch between the 5 band ranges. Hi i have this radio with antenna watson WHXX however i pick very little up also wen i do no one can here me just crackles on there end any one help please. Very informative page here, thanks for posting this. In one of your screen shots you appear to have programmed all of your repeaters as Narrow Band.

In the very next screen shot they are Wide Band. Did you switch from one Bandwidth to the other? Which are you using currently? Or at least that seems to be the case in the U. Is the Narrow Band requirement different in the UK? Thanks for your help! Gordon, Portland, Oregon. When I try to key in Regardless How I try to clear and reset, I still cannot enter what I need. Any expert can help? I did ask Quansheng about the problem but NO reply!!! Hi Pete. However, I changed to step 5 or any others, but still cannot set my frequency to I think my unit is at fault!

The COM ports match exactly. I also copied a ser2pl. I have many friends with these radios and no one has been able to get their PC to talk with the radio. Any suggestions? It puts out a very strong nearly 10 watt signal on 2 meters, however the Microphone gain is too low.

I would like to increase the microphone gain. I am very skilled with electronic equipment, e. I am sure there is a resistor or two that if replaced with a different value would increase the microphone gain.

Do you have any information that would help me make an adjustment to the mic gain? Has Quansheng stopped distributing the software? Your email address will not be published. Check here to Subscribe to notifications for new posts.

Skip to content. How To. Programming in things such as the Repeater settings on the radio itself can be a little tricky See our page Setting up the Quansheng TG-UV2 for GB3DA Danbury Repeater If you own one of these radios and want to program it — forget faffing around with the buttons on the front of the radio, and set it up from the PC.

Connecting the radio to the PC With the programming software installed, now connect the programming lead to the PC. Related Posts. Previous Post. Next Post. Anyway, keep up the good work 73 — Alan. Will promote this to the top link, and add a note. Weird, Got it now. Jesse Godin 4 October Reply. Terry 9 October Reply. Jesse Godin 7 October Reply. Thanks for trying! Nick 22 October Reply. Arne 3 November Reply. Gino 14 November Reply.

Hi, Very good tutorial! I have two questions. Thanks a lot!!! Toff 30 November Reply. James 29 November Reply. Dipendra Dev Raikut 30 November Reply. Lsl 20 December Reply. Lsl 21 December Reply. BeNiSh 20 January Reply. Robert Beswick 13 April Reply. Sebastian 2 May Reply. Sebastian 17 May Reply.

Agustin 12 May Reply. Bill 6 July Reply. This page is a step-by-step guide on how to program using PC software. Yaacov 16 August Reply. Ruan carlos 19 September Reply. Andrej 6 April Reply. Any suggestions what I did wrong?

Andrej 30 April Reply. Gemme 18 July Reply. Andrej 19 July Reply. Miguel 4 September Reply. Bob Yetman 1 November Reply. Very frustrated now! Having programed the radio how do you change the channel. Nothing in the handbook on this. Carlos Astorga 27 December Reply. Programming is freeware from Quansheng.

John 28 March Reply. John 25 April Reply. Jan Eggens 25 April Reply. Tri wahyudi 9 July Reply. Gordon 24 September Reply. Quick question: In one of your screen shots you appear to have programmed all of your repeaters as Narrow Band. Bobby 29 March Reply. Suspect you need to change the channel step.

Set it to 5 via menu option 10 and try that. John 29 March Reply. Rob 21 October Reply. Mike 7 March Reply. Ed 9 March Reply. Ken J. Add a Comment Cancel reply Your email address will not be published. Menu Search for. It is YOUR responsibility to properly word your request. To obtain Motorola software see the Sticky in the Motorola forum.

The various other vendors often permit their dealers to sell the software online i. Please use Google or some other search engine to find a dealer that sells the software. Typically each series or individual radio requires its own software package.

One package is for conventional programming and the other for trunked programming. The conventional package is more reasonable though is still several hundred dollars. The benefit is you do not need multiple versions for each radio unlike Motorola. This is a large and very visible forum. We cannot jeopardize the ability to provide the RadioReference services by allowing this activity to occur. Please respect this. JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.

Thread starter peqab Start date Sep 17, Status Not open for further replies. I have been looking around for software for this radio, quansheng tg-uv2.



0コメント

  • 1000 / 1000